Thursday, 17 October 2013

How to Bypass BIOS Passwords?

How to Bypass BIOS Passwords

BIOS passwords can add an extra layer of security for desktop and laptop computers. They are used to either prevent a user from changing the BIOS settings or to prevent the PC from booting without a password. Unfortunately, BIOS passwords can also be a liability if a user forgets their password, or changes the password to intentionally lock out the corporate IT department. Sending the unit back to the manufacturer to have the BIOS reset can be expensive and is usually not covered in the warranty. Never fear, all is not lost. There are a few known backdoors and other tricks of the trade that can be used to bypass or reset the BIOS

DISCLAIMER
This article is intended for IT Professionals and systems administrators with experience servicing computer hardware. It is not intended for home users, hackers, or computer thieves attempting to crack the password on a stolen PC. Please do not attempt any of these procedures if you are unfamiliar with computer hardware, and please use this information responsibly. LabMice.net is not responsible for the use or misuse of this material, including loss of data, damage to hardware, or personal injury.


Before attempting to bypass the BIOS password on a computer, please take a minute to contact the hardware manufacturer support staff directly and ask for their recommended methods of bypassing the BIOS security. In the event the manufacturer cannot (or will not) help you, there are a number of methods that can be used to bypass or reset the BIOS password yourself. They include:

Using a manufacturers backdoor password to access the BIOS

Use password cracking software

Reset the CMOS using the jumpers or solder beads.

Removing the CMOS battery for at least 10 minutes

Overloading the keyboard buffer

Using a professional service

Please remember that most BIOS passwords do not protect the hard drive, so if you need to recover the data, simply remove the hard drive and install it in an identical system, or configure it as a slave drive in an existing system. The exception to this are laptops, especially IBM Thinkpads, which silently lock the hard drive if the supervisor password is enabled. If the supervisor password is reset without resetting the and hard drive as well, you will be unable to access the data on the drive.

Virtual memory information



This tutorial talks about anything about the virtual memory and how much virtual memory you need for your system.


Tutorial Introduction & Background

Today application is getting bigger and bigger. Therefore, it requires a bigger system memory in order for the system to hold the application data, instruction, and thread and to load it. The system needs to copy the application data from the HDD into the system memory in order for it to process and execute the data. Once the memory gets filled up with data, the system will stop loading the program. In this case, users need to add more memory onto their system to support that intense application. However, adding more system memory costs the money and the normal user only needs to run the the intense application that requires the memory only for one or two days. Therefore, virtual memory is introduced to solve that type of problem.


Terminology & Explanation

There are two types of memory, which are as follows:

* System Memory is a memory that is used to store the application data and instruction in order for the system to process and execute that application data and instruction. When you install the memory sticks to increase the system RAM, you are adding more system memory. System Memory can be known as either the physical memory or the main memory.

* Virtual Memory is a memory that uses a portion of HDD space as the memory to store the application data and instruction that the system deemed it doesn't need to process for now. Virtual Memory can be known as the logical memory, and it controls by the Operating System, which is Microsoft Windows. Adding the Virtual Memory can be done in system configuration.


Tutorial Information & Facts or Implementation

Virtual Memory is a HDD space that uses some portion of it as the memory. It is used to store application data and instruction that is currently not needed to be process by the system.

During the program loading process, the system will copy the application data and its instruction from the HDD into the main memory (system memory). Therefore the system can use its resources such as CPU to process and execute it. Once the system memory gets filled up, the system will start moving some of the data and instruction that don't need to process anymore into the Virtual Memory until those data and instruction need to process again. So the system can call the next application data and instruction and copy it into the main memory in order for the system to process the rest and load the program. When the data and instruction that is in the Virtual Memory needs to process again, the system will first check the main memory for its space. If there is space, it will simply swap those into the main memory. If there are not any space left for the main memory, the system will first check the main memory and move any data and instructions that doesn't need to be process into the Virtual Memory. And then swap the data and instruction that need to be process by the system from the Virtual Memory into the main memory.

Having too low of Virtual Memory size or large Virtual Memory size (meaning the size that is above double of the system memory) is not a good idea. If you set the Virtual Memory too low, then the OS will keep issuing an error message that states either Not enough memory or Virtual too low. This is because some portion of the system memory are used to store the OS Kernel, and it requires to be remain in the main memory all the time. Therefore the system needs to have a space to store the not currently needed process data and instruction when the main memory get filled up. If you set the Virtual Memory size too large to support the intensive application, it is also not a good idea. Because it will create the performance lagging, and even it will take the HDD free space. The system needs to transfer the application data and instruction back and forth between the Virtual Memory and the System Memory. Therefore, that is not a good idea. The ideal size for the Virtual Memory is the default size of Virtual Memory, and it should not be exceed the value of the triple size of system memory.

To determine how much virtual memory you need, since the user's system contains the different amount of RAM, it is based on the system. By default, the OS will set the appropriate size for Virtual Memory. The default and appropriate size of Virtual Memory is:

CODE
<Amount_Of_System_Memory> * 1.5 = <Default_Appropriate_Size_Of_Virtual Memory>
.
For example, if your system contains 256 MB of RAM, you should set 384 MB for Virtual Memory.
CODE
256 MB of RAM (Main Memory) * 1.5 = 384 MB for Virtual Memory


If you would like to determine how much the Virtual Memory is for your system and/or would like to configure and add more virtual memory, follow the procedure that is shown below. The following procedure is based on windows XP Professional.

1-1) Go to right-click My Computer and choose Properties

1-2) In the System Properties dialog box, go to Advanced tab

1-3) Click Settings button that is from the Performance frame

1-4) Once the Performance Options shows up on the screen, go to Advanced tab

1-5) Under the Advanced tab, click the Change button from the Virtual Memory frame to access to the Virtual Memory setting

Then the Virtual Memory dialog box appears on the screen. In there, you are able to check how much the Virtual Memory you set. If you would like to modify the size of Virtual Memory, follow the procedure that is shown below.

2-1) In there, select the drive letter that is used to install the Operating System

2-2) Choose the option that says, "Custom Size:"

Once you choose that option, the setting for Initial Size and Maximum Size become available for you to set. Initial Size (MB) means the actual size of Virtual Memory, and Maximum Size (MB) means the maximum size of Virtual Memory that is allowed to use.

Let's say if your system contains 512 MB of RAM, then the ideal setting for the Virtual Memory is as follows:

CODE
Initial Size (MB):  768
Maximum Size (MB):  1500

Once you are happy with that Virtual Memory size, click the Set button from Paging file size for selected drive to apply the setting for the Virtual Memory size. Then click the OK button to apply the setting.

That's where you can manage and configure for the size of Virtual Memory.


Additional Information

* To maintain the good overall system performance, you should be using the default size of actual size for Virtual Memory and the triple the value of the size of the main memory for the maximum size of Virtual Memory. If you find that main memory plus virtual memory is not big enough to load the intensive application, then you will need to add more main memory onto your system.


Change the CHKDSK countdown time


When you schedule CHKDSK to run at the next boot, the system will prompt you to press a key to cancel the operation while CHKDSK is running. The system will display a countdown during that cancel period. The default value is 10 seconds. To Change this open up Regedit and locate:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager\AutoChkTimeOut
You can change the value to anything from zero to 259,200 seconds (3 days). With a timeout of zero, there is no countdown and you cannot cancel the operation

Windows 2003 System Restore, How to activate system restore in W2K3

Found this on Google, may be useful to someone!

How to install System restore on server 2003

Before we begin, you'll need an XP CD. Doesn't matter if it's home or pro. It shouldn't matter if it has a service pack on it, since all the files will be the same source. In testing i used a slipstreamed cd that already had sp1 on it.

In XP, system restore is installed in syssetup.inf under the inf.always section. If you have XP installed, you can open up %windir%\inf\syssetup.inf and search for [Infs.Always], you'll see the section xp looks at for installing system components. You'll notice it has sr.inf, this is the inf for system restore. For server 2003, if you look at syssetup.inf you won't find sr.inf. This doesn't mean system restore won't work in server 2003, it just means they didn't install it.

So first what we're going to need to do is right click on sr.inf and select 'install', to install it on server 2003. If you have xp installed on another computer/partition you can just right click on it. If you don't, then extract \i386\sr.in_ from the XP cd to your desktop, then right click on it and select 'install'. It'll prompt you where the files are, point it to the XP CD. Once done, it'll prompt to restart, say yes.

That was easy, the next part is the tricky part. After restarting you'll get an error saying the service couldn't start. Specifically the error is error 1068. I searched google and found this link -
CODE
http://www.aerdyne.com/Kbase/article_000005.htm.

The error basically means it cannot run under the service it's on. In system restore's case, it runs under the network service. I know this because in services.msc, for path to executable, it says this: C:\WINDOWS\system32\svchost.exe -k netsvcs. This got me thinking so i opened up sr.inf, and found this line:

[SRSvc_delreg]
HKLM,"Software\Microsoft\Windows NT\CurrentVersion\SvcHost","SRGroup"

I opened up regedit, and this registry key didn't exist. So it seems the sr.inf doesn't register system restore to run under the network services group. Using the above registry key as an example, i opened regedit and went to:

HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\SvcHost

On the right hand side i saw netsvcs. I double clicked on it, but saw SRService no where (SRService is the name for system restore). On a hunch, at the bottom i added SRService, rebooted, and this time got no error on startup. I opened up rstrui.exe, and system restore opened fine. I also had a System restore tab in system properties now too. I was able to make a restore point fine, then restore the computer to it without any problems. So in the above key, you want to double click on netsvcs, and at the bottom of the list, you want to type in SRService (probably case sensitive).

If you're not good with the registry you can save the following as a whatever.reg file and import it, but because it's binary i can't say if it'll work. I recommend manually adding SRService to the netsvcs key.

---copy below to whatever.reg then double click on it -----

Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\SvcHost]
"netsvcs"=hex(7):41,00,70,00,70,00,4d,00,67,00,6d,00,74,00,00,00,41,00,75,00,\
64,00,69,00,6f,00,53,00,72,00,76,00,00,00,42,00,72,00,6f,00,77,00,73,00,65,\
00,72,00,00,00,43,00,72,00,79,00,70,00,74,00,53,00,76,00,63,00,00,00,44,00,\
4d,00,53,00,65,00,72,00,76,00,65,00,72,00,00,00,45,00,76,00,65,00,6e,00,74,\
00,53,00,79,00,73,00,74,00,65,00,6d,00,00,00,48,00,69,00,64,00,53,00,65,00,\
72,00,76,00,00,00,49,00,61,00,73,00,00,00,49,00,70,00,72,00,69,00,70,00,00,\
00,49,00,72,00,6d,00,6f,00,6e,00,00,00,4c,00,61,00,6e,00,6d,00,61,00,6e,00,\
53,00,65,00,72,00,76,00,65,00,72,00,00,00,4c,00,61,00,6e,00,6d,00,61,00,6e,\
00,57,00,6f,00,72,00,6b,00,73,00,74,00,61,00,74,00,69,00,6f,00,6e,00,00,00,\
4d,00,65,00,73,00,73,00,65,00,6e,00,67,00,65,00,72,00,00,00,4e,00,65,00,74,\
00,6d,00,61,00,6e,00,00,00,4e,00,6c,00,61,00,00,00,4e,00,74,00,6d,00,73,00,\
73,00,76,00,63,00,00,00,4e,00,57,00,43,00,57,00,6f,00,72,00,6b,00,73,00,74,\
00,61,00,74,00,69,00,6f,00,6e,00,00,00,4e,00,77,00,73,00,61,00,70,00,61,00,\
67,00,65,00,6e,00,74,00,00,00,52,00,61,00,73,00,61,00,75,00,74,00,6f,00,00,\
00,52,00,61,00,73,00,6d,00,61,00,6e,00,00,00,52,00,65,00,6d,00,6f,00,74,00,\
65,00,61,00,63,00,63,00,65,00,73,00,73,00,00,00,53,00,61,00,63,00,73,00,76,\
00,72,00,00,00,53,00,63,00,68,00,65,00,64,00,75,00,6c,00,65,00,00,00,53,00,\
65,00,63,00,6c,00,6f,00,67,00,6f,00,6e,00,00,00,53,00,45,00,4e,00,53,00,00,\
00,53,00,68,00,61,00,72,00,65,00,64,00,61,00,63,00,63,00,65,00,73,00,73,00,\
00,00,54,00,68,00,65,00,6d,00,65,00,73,00,00,00,54,00,72,00,6b,00,57,00,6b,\
00,73,00,00,00,54,00,72,00,6b,00,53,00,76,00,72,00,00,00,57,00,33,00,32,00,\
54,00,69,00,6d,00,65,00,00,00,57,00,5a,00,43,00,53,00,56,00,43,00,00,00,57,\
00,6d,00,69,00,00,00,57,00,6d,00,64,00,6d,00,50,00,6d,00,53,00,70,00,00,00,\
77,00,69,00,6e,00,6d,00,67,00,6d,00,74,00,00,00,77,00,75,00,61,00,75,00,73,\
00,65,00,72,00,76,00,00,00,42,00,49,00,54,00,53,00,00,00,53,00,68,00,65,00,\
6c,00,6c,00,48,00,57,00,44,00,65,00,74,00,65,00,63,00,74,00,69,00,6f,00,6e,\
00,00,00,68,00,65,00,6c,00,70,00,73,00,76,00,63,00,00,00,75,00,70,00,6c,00,\
6f,00,61,00,64,00,6d,00,67,00,72,00,00,00,57,00,6d,00,64,00,6d,00,50,00,6d,\
00,53,00,4e,00,00,00,53,00,52,00,53,00,65,00,72,00,76,00,69,00,63,00,65,00,\
00,00,00,00


--- copy above --------------------------------------------------------

That's it! Remember to restart both times.

Do an unattended installation

The Windows XP Setup routine is much nicer than that in Windows 2000 or Windows Me, but it's still an hour-long process that forces you to sit in front of your computer for an hour, answering dialog boxes and typing in product keys. But Windows XP picks up one of the more useful features from Windows 2000, the ability to do an unattended installation, so you can simply prepare a script that will answer all those dialogs for you and let you spend some quality time with your family.
I've written about Windows 2000 unattended installations and the process is pretty much identical on Windows XP, so please read that article carefully before proceeding. And you need to be aware that this feature is designed for a standalone Windows XP system: If you want to dual-boot Windows XP with another OS, you're going to have to go through the interactive Setup just like everyone else: An unattended install will wipe out your hard drive and install only Windows XP, usually.

To perform an unattended installation, you just need to work with the Setup Manager, which is located on the Windows XP CD-ROM in D:\SupportTools\DEPLOY.CAB by default: Extract the contents of this file and you'll find a number of useful tools and help files; the one we're interested in is named setupmgr.exe. This is a very simple wizard application that will walk you through the process of creating an answer file called winnt.sif that can be used to guide Windows XP Setup through the unattended installation.

One final tip: There's one thing that Setup Manager doesn't add: Your product key. However, you can add this to the unattend.txt file manually. Simply open the file in Notepad and add the following line under the [UserData] section:

ProductID=RK7J8-2PGYQ-P47VV-V6PMB-F6XPQ

(This is a 60 day cd key)

Then, just copy winnt.sif to a floppy, put your Windows XP CD-ROM in the CD drive, and reboot: When the CD auto-boots, it will look for the unattend.txt file in A: automatically, and use it to answer the Setup questions if it's there.

Finally, please remember that this will wipe out your system! Back up first, and spend some time with the help files in DEPLOY.CAB before proceeding.

Speed up the Start Menu

The default speed of the Start Menu is pretty slow, but you can fix that by editing a Registry Key. Fire up the Registry Editor and navigate to the following key:
HKEY_CURRENT_USER \ Control Panel \ Desktop \ MenuShowDelay

By default, the value is 400. Change this to a smaller value, such as 0, to speed it up.

Remove the Shared Documents folders from My Computer

One of the most annoying things about the new Windows XP user interface is that Microsoft saw fit to provide links to all of the Shared Documents folders on your system, right at the top of the My Computer window. I can't imagine why this would be the default, even in a shared PC environment at home, but what's even more annoying is that you cannot change this behavior through the sh*ll
: Those icons are stuck there and you have to live with it.
Until now, that is.

Simply fire up the Registry Editor and navigate to the following key:
HKEY_LOCAL_MACHINE \ SOFTWARE \ Microsoft \ Windows \ CurrentVersion \ Explorer \ My Computer \ NameSpace \ DelegateFolders

You'll see a sub-key named {59031a47-3f72-44a7-89c5-5595fe6b30ee}. If you delete this, all of the Shared Documents folders (which are normally under the group called "Other Files Stored on This Computer" will be gone.

You do not need to reboot your system to see the change.

Before: A cluttered mess with icons no one will ever use (especially that orpaned one). After: Simplicity itself, and the way it should be by default.

Change your cd key

You don't need to re-install if you want to try the key out ... just do this:

1. Go to Activate Windows
2. Select the Telephone option
3. Click "Change Product Key"
4. Enter NOT ALLOWED ~ Zabref
5. Click "Update"

Now log off and log back in again. It should now show 60 days left, minus the number of days it had already counted down.

Note: If your crack de-activated REGWIZC.DLL and LICDLL.DLL, you are going to have to re-register them.

Software Not installing?


If you have a piece of software that refuses to install because it says that you are not running Windows 2000 (such as the Win2K drivers for a Mustek scanner!!) you can simply edit HKEY_LOCAL_MACHINE/SOFTWARE/Microsoft/Windows NT/CurrentVersion/ProductName to say Microsoft Windows 2000 instead of XP and it will install. You may also have to edit the version number or build number, depending on how hard the program tries to verify that you are installing on the correct OS. I had to do this for my Mustek 600 CP scanner (compatibility mode didn''t help!!!) and it worked great, so I now have my scanner working with XP (and a tech at Mustek can now eat his words).

BTW, don''t forget to restore any changes you make after you get your software installed
You do this at your own risk.

Temporarily Assign Yourself Administrative Permissions

Many programs require you to have Administrative permissions to be able to install them. Here is an easy way to temporarily assign yourself Administrative permissions while you remain logged in as a normal user.

Hold down the Shift key as you right-click on the program’s setup file.

Click Run as.

Type in a username and password that have Administrative permissions.

This will also work on applications in the Start menu.

Winxp Tips And Tricks, Winsock 2 repair



Repairing Damaged Winsock2

The symptoms when Winsock2 is damaged show when you try to release and renew the IP address using IPCONFIG...

And you get the following error message:
An error occurred while renewing interface 'Internet': An operation was attempted on something that is not a socket.

Also Internet Explorer may give the following error message:
The page cannot be displayed Additionally, you may have no IP address or no Automatic Private IP Addressing (APIPA) address, and you may be receiving IP packets but not sending them.

There are two easy ways to determine if Winsock2 is damaged:

From the XP source files, go to the Support / Tools directory


Winsock Test Method 1

Run netdiag /test:winsock
The end should say Winsock test ..... passed


Winsock Test Method 2

Run Msinfo32
Click on the + by Components
Click on the by Network
Click on Protocol
There should be 10 sections if the Winsock2 key is ok
MSAFD Tcpip [TCP/IP]
MSAFD Tcpip [UDP/IP]
RSVP UDP Service Provider
RSVP TCP Service Provider
MSAFD NetBIOS [\Device\NetBT_Tcpip...
MSAFD NetBIOS [\Device\NetBT_Tcpip...
MSAFD NetBIOS [\Device\NetBT_Tcpip...
MSAFD NetBIOS [\Device\NetBT_Tcpip...
MSAFD NetBIOS [\Device\NetBT_Tcpip...
MSAFD NetBIOS [\Device\NetBT_Tcpip...

If the names are anything different from those in this list, then likely Winsock2 is corrupted and needs to be repaired.
If you have any 3rd party software installed, the name MSAFD may be changed.
There should be no fewer than 10 sections.

To repair Winsock2

Run Regedit
Delete the following two registry keys:
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Winsock
HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Winsock2



Restart the computer
Go to Network Connections
Right click and select Properties
Click on the Install button
Select Protocol
Click on the Add button
Click on the Have Disk button
Browse to the \Windows\inf directory
Click on the Open button
Click on the OK button
Highlight Internet Protocol (TCP/IP)
Click on the OK button
Reboot 

Windows XP system response, reboot without rebooting

Have you ever been using your computer and your system suddenly stops responding in ways like it if you try to open something it just hangs? One time I tried deleting a folder and it said it was in use, but it really wasn't. If this ever happens to you, you can follow these simple steps to 'reboot' your computer without 'rebooting' it.

Press CRTL + ALT + DEL

Goto the 'processes' tab and click explorer.exe once and then click 'end process'.

Now, click File > New Task and type explorer.exe

Everything should be fine now! If the problem is major, I would recommend actually shutting down then starting up again.

Thursday, 10 October 2013

Install A New Hard-disk



Running out of hard disk space, yet also want to keep all the files that are currently on the system in perfect order? Install an extra hard disk, and see your available space rise!

Firstly, make backups of your existing system files. You may never know when these may come in handy. If your current hard disk may go down the pan, you'll be glad to have something to start with again. Also, if you want to use all your data that is on this drive, back it up anyway; ready to be transferred to the new drive. Also, create a system disk for your PC. This can be created by going to Control Panel > Add/Remove Programs, and then the "System Disk" tab. The instructions should be there for you. "WHEN I INSTALLED MY EXTRA HDD I DDNT FOLLOW ANY OF THE ABOVE MENTIONED....INSTEAD JUST OPEANED THE CABINET AND LOOKED FOR THE WIRES AND CONNECTED THEM ...ANY ONE CAN TELL WHERE THE CORRECT WIRE GOES ..... THE MAIN THING IS TO MAKE SURE THAT THE BROAD THIN GRAY WIRE OR DATA CABLE SLOT WITH THE WORD 'P2' IS CONNECTED TO THE EXTRA HDD"

Once you are prepared on the software side, turn off your PC and open the case to your PC (Please take proper precautions at this point. Anti-static wristbands and other such devices should be used. If you don't have these, just make sure you are properly earthed, and know what you are going to do. Oh, and please turn off the PC properly. I don't want you dying on me, literally!). The hard disk is the metal box shaped thing that is either the size of the floppy drive or it could be the size of the CD-Rom drive. It should be easy to spot, because it might even say "Hard Disk" on it. At this point, look and see where you can put the new drive, and how you are going to connect it up. If there is no hard drive in there, then don't worry; I'll explain how to connect it up as well.

Look at the end of the HDD. It should have a load of sockets and pins for you to play around with. At one point, you should be able to see some pins with some jumpers attached, and a sticker on another side telling you what configuration of jumper positions means what to the computer. If you are attaching it to the same IDE cable as your existing drive, then set it to "Slave", otherwise, select "Master" and fit it as close to the start of the cable as possible (The start of the cable being where it's connected to the motherboard). This cable is an "IDE" cable, and can only be fitted two ways to the drive itself. Look for an indication as to which side pin number 1 is (Look for stickers again!) and insert the IDE cable in that socket and pins, with the red side as close to pin 1 as possible. Then, just fit it into the computer, as you would do any other drive (For the thickies, which means attaching it to the case using the mounting screws that should come with the PC. Before you do this though, note down the extra information on the top of the drive, usually the number of cylinders, heads, sectors, and any other information. Next, connect one of the power cables to the HDD (These are the 4 cable collections with connectors attached, which leads from the power supply unit), and close the PC case.

Next, you will have to mess with CMOS. Turn on the PC, and hit whatever key you are told to at the bootup to get to the CMOS menus. When in there, choose the relevant section (We can't say exactly, because there are many different CMOS set-ups around) and select "IDE Auto-detection". If the hard disk does not appear on it, then you will have to enter the information manually. Use the notes you collected from the top of the hard disk earlier to tell the computer what the hard disk is.

IMPORTANT:
Afterwards, insert the system disk("THE BACKUP DISK THAT CAN BE CREATED BY RIGHT CLICKING A DRIVE4R AND SELECTING FORMAT AND THEN THE CREATE BACKUP DISK OPT") prepared earlier and "Save" your editing of the CMOS and exit. The system disk should work instead of the original hard disk (Or if you are installing from scratch, then it will boot from the A: anyway).
Type "fdisk" at the dos prompt. This runs a program called, surprisingly, FDISK. Tell the computer which drive ie the harddisk is the new one (Please choose the correct one at this point. Make a mistake, and you really could be using those backups!), and then tell it what partitions you want (Don't worry about it, as there are full instructions while you are running the program). Once this is done, you can reset your PC (Except if this drive is being installed from scratch and is on it's own. If this is the case, then you can format the drive by typing "format c:" This will format the drive for you, but what's really good is if you type "format c: /s" instead, as this installs some important files at the same time. Then, just follow the instructions to install whatever OS you are going to use.)
If you are adding this drive as a second HDD, Go into Windows (Or any other OS, but the instructions may be different!) and then format from "My Computer" like you would a floppy disk. There you go: A newly installed hard disk, with minimum effort!....and dont take the risk of formatting any of the drives u know!!!! if in doubt contact me here or don't do at all........."SOD will not be held responsible for any data lost in this process"

How to find a remote IP


Method 1


To view someone's IP# when they send you hotmail email do this:
1) Click "Options" on the upper right side of the page.
2) On the left side of the page, Click "Mail"
3) Click "Mail Display Settings"
4) Under "Message Headers" select "Full" or "Advanced"
5) Click ok

Method 2
reg a dydns account and install the ip pointer, so each time you ping the host name you regestored

for example:
you regestor the host name myhost.dydns.com, then you keep a little software running on the target host. The little software will keep update your IP to dydns.com server.

so at your pc just start cmd, and ping myhost.dydns.com, it will give you the most updated ip address.

Method 3
neverender, what doesn't work for you? Simply type in nc -vvv -l -p 80 on your box, which will set it to listen in verbose mode on port 80. Then give them a link to your IP address (for example: 111.111.111.11) and tell them to type it in their browser. The browser should resolve the address as well as append port 80 automatically. Just make sure that your friend is not very computer literate.

Method 4

Just download a very simple server such as this one and install it on your comp. Then run it and give your ip to the person you want and tell them to connect to it through a browser. Your server will log their connection and you will get their IP.

link:http://www.download.com/Abyss-Web-Server/3000-2165-10283992.html?tag=lst-0-6


Other Ways
-www.imchaos.com and make a "spy poll" to put in ur profile, this will tell u the IP of anybody who answers ur poll
-originalicons.com there is a page for doin it (i dont like it, but it works)
-or irc


Here is a more detailed tutorial about using NetCat.

http://www.onlamp.com/pub/a/onlamp/2003/05/29/netcat.html

Windows users can download NetCat from here:

http://www.atstake.com/research/tools/network_utilities/

How To Convert File System, fat - fat32 to ntfs



open a dos prompt and give the command

convert d: /fs:ntfs

this command would convert your d: drive to ntfs.

if the system cannot lock the drive, you will be prompted to convert it during next reboot.

Normally you should select yes.

Conversion from fat/fat32 to ntfs is non-destructive, your data on the drive will NOT be lost.

Be aware that converting to ntfs will make that partition of your
drive unreadable under dos unless you have ntfs utilites to do so.

How to change a CMOS Battery

First the safety rules

The inside of a computer is a bad place full of electricity and sharp edges.
On the electricity side always when working on you computer make sure that it’s still plugged in to the power socket and the power is turned off, this is to ensure that any static
From you is discharged through the earth. The inside of most computer cases are unfinished metal and has very sharp edges so be careful.

The first signs of a battery failing are:-

1) your clock starts running slowly
2) when you boot (start) your computer it has a problem finding your hardware (no hard drive, no cd rom)

To change the battery you need the following tools

1) a X-point screwdriver
2) an anti-static strap(optional)
3) a new battery (seems logical)

Then unplug all the cables from the back of the computer as you remove them make a note where they came from. (So when you finished you can put them back)

Move the computer somewhere where you can work on it with ease

Remove the cover by locating the screws around the outer edge (back) of the computer
Some computer cases only require you to remove 2 screws on one side then a panel can be removed allowing you access to the computers insides, others you must remove 6 screws and remove the whole case by sliding it to the rear and lifting it off.

Now make sure that you read the safety instructions about static.
Look inside you will see a round silver thing that looks about the size of a 10p piece (quarter). This is the battery itself, carefully lift the retaining clip and slide the battery out. That’s it removed now go to your local computer retailer, electrical retailer (Tandy/Radio shack) taking the old battery with you and get a new battery.

Back to your computer insert the new battery by lifting the clip and sliding the battery in.

Reinstall your case and plug all the cables back (you did remember to label them didn’t you)

Now for the fun part.

You will now need to go into you bios….

Right the bios is the god of your computer.

To access it, when your computer first starts you will see a black screen with white text.

If you look carefully you will see a line that says something like "press del for setup" or some other key (F2 or ESC or tab) this will take you to god's house where you can make lots of changes to the way your machine works.

It is also the place where you can make your nice computer in to a rather expensive door stop so be careful and don’t go playing with anything.

You will now be presented with a blue screen with a lot of options on it,
The one we want is load optimised/default settings.

Press the F10 key and type y the computer should now reboot.

If every thing went well then your computer will now be up and running.

Shizers way: Keep computer running. Lay it on it's side and remove side cover to expose MoBo. Take any thin object, "small screwdriver, knife point, wood shiskabob skewer. Pull back the battery retaining clip. Toss the old battery in the junk recepticle, unless you belong to greenpeace and want to save the earth. Install the new battery. No need to reset bios becasue the compter supplies voltage to the cmos while it is running. Reset or resync clock with internet. Done!

How to backup the Registry

Before you edit the registry, export the keys in the registry that you plan to edit, or back up the whole registry. If a problem occurs, you can then follow the steps how-to restore the registry to its previous state.


How to Export Registry Keys
Click Start, and then click Run.
In the Open box, type regedit, and then click OK.
On the File menu, click Export.
In the Save in box, select the boxs at the bottom the bottom according to weather you want to export all or only selected branches of the registry.
Next select a location in which to save the backup .reg file. In the File name box, type a file name, and then click Save.


How to Restore the Registry
To restore registry keys that you exported, double-click the .reg file that you saved.

Hardware Firewall

The best firewall is a hardware firewall that is completely separate from your operating system. It need not be a dedicated router, could be an old pentium box running Linux. Below I have found some sites that have How To's on setting up an outside hardware router using an old computer and using a little linux program that fits on a single floppy disk.

Brief Description:
floppyfw is a router with the advanced firewall-capabilities in Linux that fits on one single floppy disc.

Features:
Access lists, IP-masquerading (Network Address Translation), connection tracked packet filtering and (quite) advanced routing. Package for traffic shaping is also available.
Requires only a 386sx or better with two network interface cards, a 1.44MB floppy drive and 12MByte of RAM ( for less than 12M and no FPU, use the 1.0 series, which will stay maintained. )
Very simple packaging system. Is used for editors, PPP, VPN, traffic shaping and whatever comes up. (now this is looking even more like LRP (may it rest in peace) but floppyfw is not a fork.)
Logging through klogd/syslogd, both local and remote.
Serial support for console over serial port.
DHCP server and DNS cache for internal networks.

floppyfw

h#tp://www.zelow.no/floppyfw/


Sentry Firewall CD-ROM is a Linux-based bootable CDROM suitable for use as an inexpensive and easy to maintain firewall, server, or IDS(Intrusion Detection System) Node. The system is designed to be immediately configurable for a variety of different operating environments via a configuration file located on a floppy disk, a local hard drive, and/or a network via HTTP(S), FTP, SFTP, or SCP.

The Sentry Firewall CD is a complete Linux system that runs off of an initial ramdisk, much like a floppy-based system, and a CD. The default kernel is a current 2.4.x series kernel with various Netfilter patches applied. An OpenWall-patched current 2.2.x kernel is also available on the CD.

Booting from the CDROM is a fairly familiar process. The BIOS execs the boot loader(Syslinux) - which then displays a bootprompt and loads the kernel and ram-disk into memory. Once the kernel is running, the ram-disk is then mounted as root(/). At this point our configuration scripts are run(written in perl) that configure the rest of the system. It is the job of these configure scripts to put the various start up and system files into the proper location using either what is declared in the configuration file(sentry.conf) or the system defaults located in the /etc/default directory.

Most of the critical files used at boot time can be replaced with your own copy when declared in the configuration file. This is essentially how we allow the user to configure the system using his/her own configuration and in it files.

All of the binaries, files, scripts, etc, used to create the CD-ROM are also available on the CD-ROM. So, with a little practice, you can easily build and customize your own bootable Sentry Firewall CD. Please see the HOWTO for more details.

Sentry Firewall

ht*p://www.sentryfirewall.com/docs.html#overview

Hard drive gone bad



The most common problems originate from corruption of the master boot record, FAT, or directory.
Those are soft problems which can usually be taken care of with a combination of tools like Fdisk /mbr to refresh the master boot record followed by a reboot and Norton disk doctor or Spinneret.

The most common hardware problems are a bad controller, a bad drive motor, or a bad head mechanism.

1. Can the BIOS see and identify the hard drive correctly? If it can't, then the hard drives onboard controller is bad.

2. Does the drive spin and maintain a constant velocity? If it does, that's good news. The motor is functioning.

3. If the drive surges and dies, the most likely cause is a bad controller (assuming the drive is cool). A gate allowing the current to drive the motor may not be staying open. The drive needs a new controller.

4. Do you hear a lot of head clatter when the machine is turned on and initialized (but before the system attempts to access the hard drive). Head clatter would indicate that the spindle bearings are sloppy or worn badly. Maybe even lose and flopping around inside.

5. There is always the possibility that the controller you are using in the machine has gone south.

1. If the drive spins, try booting to the A> prompt, run Fdisk and check to see if Fdisk can see a partition on the hard drive. If Fdisk can see the partition, that means that it can access the drive and that the controller electronics are functioning correctly. If there is no head clatter, it may be just a matter of disk corruption which commonly occurs when a surge hits you machine and overwhelms the power supply voltage
regulator. It commonly over whelms the system electronics allowing an EM pulse to wipe out the master boot record, file allocations table, and primary directory. Fdisk can fix the master boot record and Norton Disk Doctor can restore the FAT and Directory from the secondaries.

2. The drive spins but Fdisk can't see it. Try the drive in another system and repeat the test to confirm that Fdisk can't read through the drives onboard controller. If it sees it in another system, then your machines hard drive interface is bad. You can try an upgraded or replacement controller card
like a Promise or CMD Technologies (there are others) in you machine after disabling the integrated controller in the BIOS, but if the integrated controller went south, it may just be
symptomatic of further failures and you'd be wise to replace the motherboard. Trying the drive in another machine also eliminates the variable that your machines 12 volt power output being bad

3. If you get head clatter but a constant velocity on the drive motor (no surging), you might try sticking the hard drive in the freezer for about 12 hours. This is an old trick from back in the days of the MFM/ESDI driver era. This can cause the drive components to shrink enough to make the track
marker align with the tracks. We don't see that kind of platter spindle wear much anymore, but back in the old days, the balancing and bearings weren't as good. Still, under the right circumstances, it might help. It would depend on how old the drive is and how many hours of wear have occurred. You
have to be quick to get your info off the drive when it works. Back then, the drives were much smaller, so there wasn't so much to copy. So, go after the important data first.

4. The drive doesn't spin. Either the onboard controller is bad or the motor is bad (assuming you did try the drive in another machine). It's time to hit the net and local independent shops to see if you can locate another drive of  the same make and model that's good. Since the drive is probably an older drive and no longer in distribution, your best bet is to find an identical used drive. If you know someone with the same make and model, you might be wise to try and persuade them to sell you their drive with an offer of providing them with a free upgraded drive. If you can locate an identical drive, start with the controller replacement ...
this is the simplest and least invasive. If swapping the controller doesn't produce the desire result, you can tear into the drive and swap the motors. While you have both drive
opened up to accomplish this, scrutinize the platters, heads and armatures. You might even hook the drive up and power it from a system with both drives attached. This way, you could
see anything that deviates between the actions of both drives when they are initialized. Swapping patters is unlikely to produce any positive result. They are a balanced system like the tires on your car and I suspect that the balance will be different for each drive as will other variables.

5. There's always Ontrack Corp. who will attempt to recoup your info starting at $500 and going up from there. They don't fix and return the drive either. If the info is all that important to you, I would seek some
professional and experience technician in your locality who makes his living from servicing and building computer systems ... not just selling them. If you have had much experience
salvaging information from bad hard drives, your likelihood of success is low. In the case of soft corruption, all utilities have their eccentricities. Often times, Norton Disk Doctor will go too far (if you let it). It's wise to just let those utilities small steps and then have a look at the drive and see if you can copy it off. Norton will go so far as to rename directories and files, and even delete them or break them up into fragments which are useless.

Cracking BIOS

Here is the best way to crack the bios password in win 95/98:

Follow the steps below:

1) Boot up windows.
2) go to dos-prompt or go to command prompt directly from the windows start up menu.
3) type the command at the prompt: "debug" (without quotes )
4) type the following lines now exactly as given.......
o 70 10
o 71 20
      quit
      exit
4) exit from the dos prompt and restart the machine


password protection gone!!!!!!!!!!!!!
EnjoYYYYYYYYYY

PS: I tested this in Award Bios........
There seems to be some issue regarding display drivers on some machines if this is used. Just reinstall the drivers, Everything will be fine...........

I have not found any other trouble if the codes are used.
To be on safe side, just back up your data..........
The use of this code is entirely at ur risk.......... It worked fine for me.

Wednesday, 9 October 2013

Boot Block Recovery For Free



You don't need to pay a measly sum of dollars just to recover from a boot block mode. Here it is folks:

AWARD Bootblock recovery:

That shorting trick should work if the boot block code is not corrupted, and it should not be if /sb switch is used when flashing the bios (instead of /wb switch).

The 2 pins to short to force a checksum error varies from chip to chip. But these are usually the highest-numbered address pins (A10 and above).

These are the pins used by the system to read the System BIOS (original.bin for award v6), calculate the ROM checksum and see if it's valid before decompressing it into memory, and subsequently allow Bootblock POST to pass control over to the System BIOS.

You just have to fool the system into believing that the System BIOS is corrupt. This you do by giving your system a hard time reading the System BIOS by shorting the 2 high address pins. And when it could not read the System BIOS properly, ROM Checksum Error is detected "so to speak" and Bootblock recovery is activated.

Sometimes, any combination of the high address pins won't work to force a checksum error in some chips, like my Winbond W49F002U. But shorting the #WE pin with the highest-numbered address pin (A17) worked for this chip. You just have to be experimentative if you're not comfortable with "hot flashing" or "replacement BIOS".

But to avoid further damage to your chip if you're not sure which are the correct pins to short, measure the potential between the 2 pins by a voltmeter while the system is on. If the voltage reading is zero (or no potential at all), it is safe to short these pins.

But do not short the pins while the system is on. Instead, power down then do the short, then power up while still shorting. And as soon as you hear 3 beeps (1 long, 2 short), remove the short at once so that automatic reflashing from Drive A can proceed without errors (assuming you had autoexec.bat in it).

About how to do the shorting, the tip of a screwdriver would do. But with such minute pins on the PLCC chip, I'm pretty comfortable doing it with the tip of my multi-tester or voltmeter probe. Short the pins at the point where they come out of the chip.


AMIBIOS Recovery bootblock:
1. Copy a known working BIOS image for your board to a floppy and rename it to AMIBOOT.ROM.
2. Insert the floppy in your system's floppydrive.
3. Power on the system while holding CTRL+Home keys. Release the keys when you hear a beep and/or see the floppy light coming on.
4 . Just wait until you hear 4 beeps. When 4 beeps are heard the reprogramming of the System Block BIOS went succesfull, so then you may restart your system.

Some alternative keys that can be used to force BIOS update (only the System Block will be updated so it's quite safe):
CTRL+Home= restore missing code into system block and clear CMOS when programming went ok.
CTRL+Page Up= restore missing code into system block and clear CMOS or DMI when programming went ok.
CTRL+Page Down= restore missing code into system block and do not clear CMOS and DMI area when programming went ok
Btw: the alternative keys work only with AMIBIOS 7 or higher (so for example an AMI 6.26 BIOS can be only recovered by using CTRL+Home keys).
Boot Block Recovery for FREE

************************************************
BLACKOUT Flashing
*************************************************

Recovering a Corrupt AMI BIOS chip
With motherboards that use BOOT BLOCK BIOS it is possible to recover a corrupted BIOS because the BOOT BLOCK section of the BIOS, which is responsible for booting the computer remains unmodified. When an AMI BIOS becomes corrupt the system will appear to start, but nothing will appear on the screen, the floppy drive light will come on and the system will access the floppy drive repeatedly. If your motherboard has an ISA slot and you have an old ISA video card lying around, put the ISA video card in your system and connect the monitor. The BOOT BLOCK section of the BIOS only supports ISA video cards, so if you do not have an ISA video card or your motherboard does not have ISA slots, you will have to restore your BIOS blind, with no monitor to show you what’s going on.

AMI has integrated a recovery routine into the BOOT BLOCK of the BIOS, which in the event the BIOS becomes corrupt can be used to restore the BIOS to a working state. The routine is called when the SYSTEM BLOCK of the BIOS is empty. The restore routine will access the floppy drive looking for a BIOS file names AMIBOOT.ROM, this is why the floppy drive light comes on and the drive spins. If the file is found it is loaded into the SYSTEM BLOCK of the BIOS to replace the missing information. To restore your BIOS simply copy a working BIOS file to a floppy diskette and rename it AMIBOOT.ROM, then insert it into the computer while the power is on. The diskette does not need to be bootable or contain a flash utility. After about four minutes the system will beep four times. Remove the floppy diskette from the drive and reboot the computer. The BIOS should now be restored.

Recovering a Corrupt AWARD BIOS

With AWARD BIOS the process is similar but still a bit different. To recover an AWARD BIOS you will need to create a floppy diskette with a working BIOS file in .BIN format, an AWARD flash utility and an AUTOEXEC.BAT file. AWARD BIOS will not automatically restore the BIOS information to the SYSTEM BLOCK for this reason you will need to add the commands necessary to flash the BIOS in the AUTOEXEC.BAT file. The system will run the AUTOEXE.BAT file, which will in turn flash the BIOS. This is fairly easy. Here are the steps you need to take.

· Create a bootable floppy diskette
· Copy the BIOS file and flash utility to the diskette
· Create an text file with any standard text editor and add the following lines

@ECHO OFF
FLASH763 BIOSFILE.BIN /py

In the above example I am assuming that you are using the FLASH763.EXE flash utility. You will need to replace the FLASH763 with the name of whatever flash utility you are using, and replace the BIOSFILE.BIN with the name of the BIOS file you are using. You will also need to change the ‘/py’ to whatever the command is for your flash utility to automatically program the BIOS without user intervention. If you do not know the command to automatically flash your BIOS type the name of the flash utility with a space and then /? to display the utility’s help screen. The help screen should pecify the command switch to automatically flash your BIOS. If you are using the FLASH763.EXE utility then the switch to automatically flash your BIOS is ‘/py’.
BIOS Update Procedure

All latest Motherboards today, 486/ Pentium / Pentium Pro etc.,ensure that upgrades are easily obtained by incorporating the system BIOS in a FLASH Memory component. With FLASH BIOS, there is no need to replace an EPROM component. Once downloaded, the upgrade utility fits on a floppy disc allowing the user to save, verify and update the system BIOS. A hard drive or a network drive can also be used to run the newer upgrade utilities. However, memory managers can not be installed while upgrading.

Most pre-Pentium motherboards do not have a Flash BIOS. The following instructions therefore do not apply to these boards. If your motherboard does not have a Flash BIOS (EEPROM) you will need to use an EPROM programmer to re-program the BIOS chip. See your dealer for more information about this.

Please read the following instructions in full before starting a Flash BIOS upgrade:
A. Create a Bootable Floppy (in DOS)

•With a non-formatted disk, type the following:
format a:/s
•If using a formatted disk, type:
sys a:

This procedure will ensure a clean boot when you are flashing the new BIOS.

B. Download the BIOS file
•Download the correct BIOS file by clicking on the file name of the BIOS file you wish to download.
•Save the BIOS file and the Flash Utility file in the boot disk you have created. Unzip the BIOS file and the
flash utility file. If you don't have an "unzip" utility, download the WinZip for Windows 95 shareware/ evaluation copy for that one time use from _www.winzip.com or _www.pkware.com. Most CD ROMs found in computer magazines, have a shareware version of WinZip on them.

•You should have extracted two files:

Flash BIOS utility eg: flash7265.exe (for example)
BIOS eg: 6152J900.bin (example)

Use the latest flash utility available unless otherwise specified (either on the BIOS update page or in the archive file). This information is usually provided.

C. Upgrade the System BIOS
During boot up, write down the old BIOS version because you will need to use it for the BIOS backup file name.

Place the bootable floppy disk containing the BIOS file and the Flash Utility in drive a, and reboot the system in MS-DOS, preferably Version 6.22

•At the A:> prompt, type the corresponding Flash BIOS utility and the BIOS file with its extension.

For example:
flash625 615j900.bin

•From the Flash Memory Writer menu, select "Y" to "Do you want to save BIOS?" if you want to save (back up) your current BIOS (strongly recommended), then type the name of your current BIOS and its extension after FILE NAME TO SAVE: eg: a:\613J900.bin

Alternatively select "N" if you don't want to save your current BIOS. Beware, though, that you won't be able to recover from a possible failure.

•Select "Y" to "Are you sure to program?"
•Wait until it displays "Message: Power Off or Reset the system"

Once the BIOS has been successfully loaded, remove the floppy disk and reboot the system. If you write to BIOS but cannot complete the procedure, do not switch off, because the computer will not be able to boo, and you will not be given another chance to flash. In this case leave your system on until you resolve the problem (flashing BIOS with old file is a possible solution, provided you've made a backup before)

Make sure the new BIOS version has been loaded properly by taking note of the BIOS identifier as the system is rebooting.

For AMI BIOS
Once the BIOS has been successfully loaded, remove the floppy disk and reboot the system holding the "END" key prior to power on until you enter CMOS setup. If you do not do this the first time booting up after upgrading the BIOS, the system will hang.

BIOS Update Tips
note:
1.Make sure never to turn off or reset your computer during the flash process. This will corrupt the BIOS data. We also recommend that you make a copy of your current BIOS on the bootable floppy so you can reflash it if you need to. (This option is not available when flashing an AMI BIOS).

2. If you have problems installing your new BIOS please check the following:
Have you done a clean boot?
In other words, did you follow the above procedure for making a bootable floppy? This ensures that when booting from "A" there are no device drivers on the diskette. Failing to do a clean boot is the most common cause for getting a "Memory Insufficient" error message when attempting to flash a BIOS.

If you have not used a bootable floppy, insure a clean boot either by

a) pressing F5 during bootup

b) by removing all device drivers on the CONFIG.SYS including the HIMEM.SYS. Do this by using the EDIT command.

Have you booted up under DOS?
Booting in Windows is another common cause for getting a "Memory Insufficient" error message when attempting to flash a BIOS. Make sure to boot up to DOS with a minimum set of drivers. Important: Booting in DOS does not mean selecting "Restart computer in MS-DOS Mode" from Windows98/95 shutdown menu or going to Prompt mode in WindowsNT, but rather following the above procedure (format a: /s and rebooting from a:\).

Have you entered the full file name of the flash utility and the BIOS plus its extension?
Do not forget that often you will need to add a drive letter (a:\) before flashing the BIOS. Example: when asked for file name of new BIOS file which is on your floppy disk, in case you're working from c:\ your will need to type a:\615j900.bin, rather than 615j900.bin only.

Beep Code manual

Beep Code Manual, Better Than Gold Techies, American Megatrends Int. & Phoenix

(I'm IT, I use these codes to trouble shoot hardware issues at my job. Enjoy) cold.gif

BIOS Beep Codes
When a computer is first turned on, or rebooted, its BIOS performs a power-on self test (POST) to test the system's hardware, checking to make sure that all of the system's hardware components are working properly. Under normal circumstances, the POST will display an error message; however, if the BIOS detects an error before it can access the video card, or if there is a problem with the video card, it will produce a series of beeps, and the pattern of the beeps indicates what kind of problem the BIOS has detected.

  • Because there are many brands of BIOS, there are no standard beep codes for every BIOS.
  • The two most-used brands are AMI (American Megatrends International) and Phoenix.
  • Below are listed the beep codes for AMI systems, and here are the beep codes for Phoenix systems.

AMI Beep Codes

Beep Code Meaning
1 beep DRAM refresh failure. There is a problem in the system memory or the motherboard.
2 beeps Memory parity error. The parity circuit is not working properly.
3 beeps Base 64K RAM failure. There is a problem with the first 64K of system memory.
4 beeps System timer not operational. There is problem with the timer(s) that control functions on the motherboard.
5 beeps Processor failure. The system CPU has failed.
6 beeps Gate A20/keyboard controller failure. The keyboard IC controller has failed, preventing gate A20 from switching the processor to protect mode.
7 beeps Virtual mode exception error.
8 beeps Video memory error. The BIOS cannot write to the frame buffer memory on the video card.
9 beeps ROM checksum error. The BIOS ROM chip on the motherboard is likely faulty.
10 beeps CMOS checksum error. Something on the motherboard is causing an error when trying to interact with the CMOS.
11 beeps Bad cache memory. An error in the level 2 cache memory.
1 long beep, 2 short Failure in the video system.
1 long beep, 3 short A failure has been detected in memory above 64K.
1 long beep, 8 short Display test failure.
Continuous beeping A problem with the memory or video.
BIOS Beep Codes


Phoenix Beep Codes
Phoenix uses sequences of beeps to indicate problems. The "-" between each number below indicates a pause between each beep sequence. For example, 1-2-3 indicates one beep, followed by a pause and two beeps, followed by a pause and three beeps. Phoenix version before 4.x use 3-beep codes, while Phoenix versions starting with 4.x use 4-beep codes. Click here for AMI BIOS beep codes.
4-Beep Codes
Beep Code Meaning
1-1-1-3 Faulty CPU/motherboard. Verify real mode.
1-1-2-1 Faulty CPU/motherboard.
1-1-2-3 Faulty motherboard or one of its components.
1-1-3-1 Faulty motherboard or one of its components. Initialize chipset registers with initial POST values.
1-1-3-2 Faulty motherboard or one of its components.
1-1-3-3 Faulty motherboard or one of its components. Initialize CPU registers.
1-1-3-2
1-1-3-3
1-1-3-4 Failure in the first 64K of memory.
1-1-4-1 Level 2 cache error.
1-1-4-3 I/O port error.
1-2-1-1 Power management error.
1-2-1-2
1-2-1-3 Faulty motherboard or one of its components.
1-2-2-1 Keyboard controller failure.
1-2-2-3 BIOS ROM error.
1-2-3-1 System timer error.
1-2-3-3 DMA error.
1-2-4-1 IRQ controller error.
1-3-1-1 DRAM refresh error.
1-3-1-3 A20 gate failure.
1-3-2-1 Faulty motherboard or one of its components.
1-3-3-1 Extended memory error.
1-3-3-3
1-3-4-1
1-3-4-3 Error in first 1MB of system memory.
1-4-1-3
1-4-2-4 CPU error.
1-4-3-1
2-1-4-1 BIOS ROM shadow error.
1-4-3-2
1-4-3-3 Level 2 cache error.
1-4-4-1
1-4-4-2
2-1-1-1 Faulty motherboard or one of its components.
2-1-1-3
2-1-2-1 IRQ failure.
2-1-2-3 BIOS ROM error.
2-1-2-4
2-1-3-2 I/O port failure.
2-1-3-1
2-1-3-3 Video system failure.
2-1-1-3
2-1-2-1 IRQ failure.
2-1-2-3 BIOS ROM error.
2-1-2-4 I/O port failure.
2-1-4-3
2-2-1-1 Video card failure.
2-2-1-3
2-2-2-1
2-2-2-3 Keyboard controller failure.
2-2-3-1 IRQ error.
2-2-4-1 Error in first 1MB of system memory.
2-3-1-1
2-3-3-3 Extended memory failure.
2-3-2-1 Faulty motherboard or one of its components.
2-3-2-3
2-3-3-1 Level 2 cache error.
2-3-4-1
2-3-4-3 Motherboard or video card failure.
2-3-4-1
2-3-4-3
2-4-1-1 Motherboard or video card failure.
2-4-1-3 Faulty motherboard or one of its components.
2-4-2-1 RTC error.
2-4-2-3 Keyboard controller error.
2-4-4-1 IRQ error.
3-1-1-1
3-1-1-3
3-1-2-1
3-1-2-3 I/O port error.
3-1-3-1
3-1-3-3 Faulty motherboard or one of its components.
3-1-4-1
3-2-1-1
3-2-1-2 Floppy drive or hard drive failure.
3-2-1-3 Faulty motherboard or one of its components.
3-2-2-1 Keyboard controller error.
3-2-2-3
3-2-3-1
3-2-4-1 Faulty motherboard or one of its components.
3-2-4-3 IRQ error.
3-3-1-1 RTC error.
3-3-1-3 Key lock error.
3-3-3-3 Faulty motherboard or one of its components.
3-3-3-3
3-3-4-1
3-3-4-3
3-4-1-1
3-4-1-3
3-4-2-1
3-4-2-3
3-4-3-1
3-4-4-1
3-4-4-4 Faulty motherboard or one of its components.
4-1-1-1 Floppy drive or hard drive failure.
4-2-1-1
4-2-1-3
4-2-2-1 IRQ failure.
4-2-2-3
4-2-3-1
4-2-3-3
4-2-4-1 Faulty motherboard or one of its components.
4-2-4-3 Keyboard controller error.
4-3-1-3
4-3-1-4
4-3-2-1
4-3-2-2
4-3-3-1
4-3-4-1
4-3-4-3 Faulty motherboard or one of its components.
4-3-3-2
4-3-3-4 IRQ failure.
4-3-3-3
4-3-4-2 Floppy drive or hard drive failure.
3-Beep Codes
Beep Code Meaning
1-1-2 Faulty CPU/motherboard.
1-1-3 Faulty motherboard/CMOS read-write failure.
1-1-4 Faulty BIOS/BIOS ROM checksum error.
1-2-1 System timer not operational. There is a problem with the timer(s) that control functions on the motherboard.
1-2-2
1-2-3 Faulty motherboard/DMA failure.
1-3-1 Memory refresh failure.
1-3-2
1-3-3
1-3-4 Failure in the first 64K of memory.
1-4-1 Address line failure.
1-4-2 Parity RAM failure.
1-4-3 Timer failure.
1-4-4 NMI port failure.
2-_-_ Any combination of beeps after 2 indicates a failure in the first 64K of memory.
3-1-1 Master DMA failure.
3-1-2 Slave DMA failure.
3-1-3
3-1-4 Interrupt controller failure.
3-2-4 Keyboard controller failure.
3-3-1
3-3-2 CMOS error.
3-3-4 Video card failure.
3-4-1 Video card failure.
4-2-1 Timer failure.
4-2-2 CMOS shutdown failure.
4-2-3 Gate A20 failure.
4-2-4 Unexpected interrupt in protected mode.
4-3-1 RAM test failure.
4-3-3 Timer failure.
4-3-4 Time of day clock failure.
4-4-1 Serial port failure.
4-4-2 Parallel port failure.
4-4-3 Math coprocessor.

Auto End Task to Enable a Proper Shutdown

 Auto End Tasks to Enable a Proper Shutdown

This reg file automatically ends tasks and timeouts that prevent programs from shutting down and clears the Paging File on Exit.

1. Copy the following (everything in the box) into notepad.

QUOTE
Windows Registry Editor Version 5.00

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Session Manager\Memory Management]
"ClearPageFileAtShutdown"=dword:00000001

[HKEY_USERS\.DEFAULT\Control Panel\Desktop]
"AutoEndTasks"="1"

[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control]
"WaitToKillServiceTimeout"="1000"


2. Save the file as shutdown.reg
3. Double click the file to import into your registry.

NOTE: If your anti-virus software warns you of a "malicious" script, this is normal if you have "Script Safe" or similar technology enabled.

A small tutorial for Real meadia player

You may find this helpful if you donwload hundreds of short episodes in rm format like me and tired of double-click to open next files.

Very easy. Use notepad to open a new file, type this inside:
file://link to file1
file://link to file2
(type as many as you want)
Close file. Rename it to FileName.rm

Then you`re done!!!!

Ex:
I put my playlist file here: C:\Movies\7VNR
And the movie files are in C:\Movies\7VNR\DragonBall

Then inside my playlist file I`ll have something like this:

file://DragonBall/db134.rm
file://DragonBall/db135.rm
file://DragonBall/db136.rm
file://DragonBall/db137.rm
file://DragonBall/db138.rm

16x Dvd+-rw Dl Dvd Writer Comparison Guide

Source:
CODE
http://www.extrememhz.com/dlcomp-p1.shtml


Since the introduction of double layer DVD writers, the interest has been quite overwhelming and is why we keep bringing you reviews of these highly popular drives. The anticipation has now turned into down right obsession and it has become a key component in any current or new system build, thanks to the declining prices and continued media hype. Manufacturers are quite aware of the fascination and is why they have each been releasing their own products which excel in at least one area of the testing methodology used in most reviews. This has led to some confusion as to which drive is best suited for the individuals needs. Today, we compare four 16x double layer drives and highlight both the strong and weak points in order to give you a better idea of which drive is best suited for you.


In this comparison guide, we will be looking at four of the top 16x drives to hit the market, the Pioneer DVR-108, NEC ND3500A, Lite-On SOHW-1633s and the new LG GSA-4160B. We will cover everything from design and features to performance and price. Let's begin with a quick look at each of these drives.


As far as the front bezel design goes, the LG-GSA4160B is by far the most attractive drive of the bunch. However, for those who are looking for a headphone jack, the Lite-On drive is the only DL writer offering a headphone jack, as well as volume control. The Pioneer and NEC drives, in my opinion, are the ugliest drives, with a very plain look that just wants to make you hide the drive period. Although we only obtained the 4160B in black, all these drives are offered with both white and black bezels. If you opt for the more expensive Pioneer "XL" model, it has the most impressive looks of any drive in the market. However, this will come at a very hefty price tag, considering they contain different firmware as well that offer a few extra features.

So, we have determined which is the sexiest-looking drive, but what about performance? I've done some extensive testing on each model to determine which is indeed the most impressive of the bunch. But before we show you performance results, let's briefly look at the features and what they have to offer.

Features
Each one of these drives has there disappointments when it comes to features. Let's compare each to see what they really offer.

DVD Writing
DVD+R DVD-R DVD+RW DVD-RW
LG GSA-4160B 16x 8x 4x 4x
Lite-On SOHW-1633s 16x 8x 4x 4x
NEC ND-3500A 16x 16x 4x 4x
Pioneer DVR-108 16x 16x 4x 4x

While all these drives are indeed 16x models, only two will write to both formats at this speed. The LG GSA-4160B and the Lite-On SOHW-1633s only support 8x DVD-R writing. So if you are one who only prefers this format, the NEC or Pioneer would be the best choice. All of these drives support writing to DVD re-writable media at 4x.

DVD+R9 Double Layer Writing

Write Speed
LG GSA-4160B 2.4x
Lite-On SOHW-1633s 2.4x
NEC ND-3500A 4x
Pioneer DVR-108 4x

The major disappointment with both the LG and the Lite-On 16x drives is the lack of 4x double layer writing support. Pioneer and NEC seem to be the only manufacturers to jump in and release second generation double layer drives supporting much faster 4x writing. In fact, the jump from 2.4x to 4x is quite substantial as we will show you a bit later in this comparison.


DVD-RAM Support
Supported Read Write
LG GSA-4160B YES 5x 5x
Lite-On SOHW-1633s NO NO NO
NEC ND-3500A NO NO NO
Pioneer DVR-108 YES 2x NO

Now this is where both the LG GSA-4120B and GSA-4160B shine above the rest. In fact, it is what has made these drives the most popular DVD writers on the market. Unlike the rest in the roundup, it is a triple format burner, offering full support for DVD-RAM media. The other drives do not support it, with the exception of the Pioneer DVR-108 which supports reading of DVD-RAM discs at 2x. I personally don't see the point in offering only read capabilities, but it's at least one extra feature added to distinguish it from the rest. Fast 5x support of the LG GSA-4160 will actually be tested a bit later in this article.


CDR Writing

CDR CDRW
LG GSA-4160B 40x 24x
Lite-On SOHW-1633s 48x 24x
NEC ND-3500A 48x 24x
Pioneer DVR-108 32x 24x

The fastest CDR writers of the bunch are the Lite-On SOHW-1633s and the NEC ND-3500A. With their support for 48x writing, they make a great all-in-one drive for many users. The only drive lacking in this lineup is the Pioneer DVR-108. Why they opted for only 32x writing is still quite puzzling and is actually why I have found that many are choosing the NEC over the Pioneer. The LG GSA-4160B should not be left out of consideration though. We will show you later that the difference in write times between 40x and 48x is not much to brag about.



Bitsetting Support
One feature I've found that is most important for many users is bitsetting support. Let's compare these drives and see what they offer.

DVD+R/RW Support DVD+R DL Support
LG GSA-4160B NO NO
Lite-On SOHW-1633s YES NO
NEC ND-3500A NO YES
Pioneer DVR-108 NO YES

The LG GSA-4160B does not offer bitsetting support out of the box. However, it is very likely that you will be able to obtain support through an excellent third-party tool called DVDInfo Pro. Right now, they only support the GSA-4120B, but I'm confident with the author that support for this drive will be likely. LG firmware is very hard to hack, however some select few have been able to do so. Using Lite-On's booktype utility, you can change the booktype of DVD+R/RW media, however, the firmware does not automatically change booktype of DVD+R DL discs to DVD-ROM like the NEC and Pioneer models do.


Additional Features
As far as other features go, all these drives have a 2MB buffer but offer some sort of buffer under-run protection, which all work exceptionally well. This is especially useful if you will be burning discs at 16x, which I personally don't recommend just yet. As our individual tests of these drives revealed, burning at this speed is quite unstable, with the exception of the Lite-On SOHW-1633s.